Showing posts with label Studio Lighting. Show all posts
Showing posts with label Studio Lighting. Show all posts

Sunday, January 26, 2014

Creative Lighting with Color

It is possible to use light as an element of creation in the production of a photo. Besides varying the position of the flashes or other lighting and their intensity, one can also change the color of the lighting so that the colors in the photo appear differently from how the subject appears to the eye without the lighting. To change the color of the lighting one uses lighting gels (also called colored gels). There are hundreds of lighting gels on the market each a different shade of a different color so that the lighting effects one can produce are endless. The aim is to produce a photo that is unlike what you can see with your eye. This particular photo was inspired by the artist Picasso's use of color, although you could take cues from any number of painters and artists.

For this setup I used three flash units with gels. You could experiment with using only two flash units, but the colors may not turn out as intense, and you run the risk of there being shadows where you do not want them. Of course there is nothing keeping you from using more flash units. By all means you should experiment with the lighting and the color of the gels to achieve what you wish to achieve with the photos. You will want an area where you can control the ambient lighting such as a studio as ambient light can affect the colors you wish to produce in the photograph. A way to dim the lights to just the point where you can see what you are doing is also desired. If you are not shooting in a studio, but say in a living room of a house, sunlight streaming in from a window can have dire effects on what you are trying to achieve with the colors as can light from street lights if you are shooting at night. If you do not have a studio available, you should try to find a windowless room in your home, or a room where you can put up heavy curtains to block out light. Use of a tripod as this will give more control if you are using a continuos light source. Camera movement could affect what you are wanting to achieve in undesired ways. A remote release is also advised to minimize camera movement. If you do not have a remote release you can use the camera's timer to keep movement to a minimum. Once you are setup, you will want to experiment with your camera settings to see what you can do. 

This particular photo was taken with a Canon 7D with an EF-S 18-200mm lens set to 50mm. The ISO was set at 400 and the aperture was set at f8. The shutter speed was at 1/200th of a second while white balance was set to 5600k. It was saved in the RAW format. Three flash units were used. A pair of 430EX-IIs were used to light the background, one from camera left, and one from camera right. Both used yellow gels. The subject herself was lit by a single 580EX-II at a 90 degree angle with a blue gel. You can experiment with the colors of the gels to get the best color as not all gels are created equal. With hundreds of gels on the market there is no reason you should not be able to achieve your desired color in a photograph. You can also experiment with the position of the flash units and the type. Using different flash units in different positions you can achieve different effects. By all means experiment with your camera settings.

Lighting with lighting gels is an area where one can feel free to experiment, and it can be argued that you are not so much a photographer using lighting gels as you are an artist. After all you are not recording the image as it appears to the naked eye, but attempting to produce something the eye does not see, something that can only be captured in the instant of flash units and the "click" of a shutter. To get ideas I recommend looking at the artwork of famous painters such as Picasso in his Blue Period for inspiration. Painting your subject, background, or both with colored light opens up a world of creativity.




Follow Us



Sunday, September 29, 2013

What is High Speed Sync?

1/3200th w/ High Speed Sync
1/3200th w/ High Speed Sync

High Speed Sync is a dedicated flash camera function that allows the photographer to use flash in situations where the lighting requires a shutter speed that would otherwise prohibit the use of flash. 

Ok that statement is a bit high on the techno speak, so lets look at it a bit differently. In most flash photography shutter speed is pretty irrelevant, the lighting situation is such that the ambient light leaves little or no impression on the sensor and the flash dictates both the exposure and acts to freeze the action. In photography without flash the aperture is used to control depth of field while the shutter acts to control action - a slow shutter shows motion blur and a fast shutter freezes objects in motion. With flash photography even in cases where you are blending with ambient light the flash will still have a tendency to freeze action. This happens because the short, high intensity burn of the flash acts as the effective shutter speed, usually somewhere around 1/1000th of a second depending on flash output.

I mention this because it can be easy to forget if you do not regularly shoot in situations where it is necessary to shoot outside of the cameras sync speed. When the flash is freezing your action for you it is easy to forget that the flash does not function with the camera at shutter speeds above the camera sync - for most cameras this will be 1/250th of a second, though for the EOS 6D that speed is 1/180th. To find your Camera’s sync speed you will need to check the camera's user manual.

Ok since we have established that flash freezes action and it is therefore not necessary to use the shutter to do that then why do you need to be able to use flash with a shutter set above the sync speed? Well sometimes the ambient light you are blending with is just too bright for your camera’s sync speed, this generally means you are shooting in sunlight. 

Second Curtain Closing
Second Curtain Closing
To understand this a little better it lets take a moment to look at how the shutter functions. At and below sync speed the first curtain of the shutter opens completely before the second curtain starts to close, this allows the entire sensor to be exposed at once. At speeds above the camera’s sync speed the second curtain starts to close before the first curtain has fully opened, at higher speeds only a partial strip of the sensor is being exposed at any given moment.

High Speed Sync changes the duration of the flash burn. Instead of the flash firing once the first curtain has cleared the shutter the flash fires a series of pulses and burns for the entire duration of the shutter action. This function allows the flash to be lit for every section of the sensor without the second curtain blocking part of the sensor which happens if the flash fires a single burst.

The Image at the top of the post was photographed using High Speed Sync. That image was taken at 1/3200th of a second, well out side of the camera’s normal sync speed. The next two images show the scene without flash, the first at 1/180th of a second which exposed the apple nicely but completely blew out the sky, the second at 1/3200th which was the speed needed to get proper exposure of the sky but it crushed the apple in shadow leaving it and the leaves quite dark. It would be possible to create an HDR of this scene, but for HDR you really need to be shooting still life. High Speed Sync can create the image in a single exposure and allows blend flash with sunlight, something the regular sync speed does not allow.

1/180th no flash
1/180th no flash

1/3200th no flash
1/3200th no flash

* Note not all flashes and cameras support High Speed Sync though it is available on Canon, Nikon, and Sony Alpha lines, as well as being supported by some third party flashes. You will need to consult both your camera and flash manuals to see if High Speed Sync is an option for you.



Follow Us



Sunday, September 1, 2013

Blending Flash with Ambient Light


Lighting Set-Up
Lighting Set-Up
Mixing strobes with existing light seems to be one of those things that confuses many photographers. This is most likely due to the fact that two sets of photographic rules are at play when blending flash and ambient light. The first set is what natural light shooters tend to live and die by, the “BIG 3”. If you have read my earlier blog post you know that I tend to look at this set of rules as being very malleable. The second set of rules come out of studio lighting, where light is controlled by light, or by aperture if you are working with a set of strobes that are not adjustable (but even in this case you can control flash power by distance to the subject or the use of neutral density gels and not need to use on camera settings).

So where does the confusion come in? When a photographer is shooting using all natural light where they have very little or no control over the light, such as landscapes, their only recourse is to adjust camera settings. If the scene is already properly exposed and the photographer wishes to adjust shutter, they then have to adjust aperture or ISO to get an equivalent exposure. In the days of film they were really stuck with adjusting aperture or wasting the rest of a roll of film to change ISO/ASA.

When shooting under studio strobes shutter speed is almost meaningless. A simple way to demonstrate this is to set a camera up in a room on manual setting. Set the ISO, shutter aperture and flash for the exposure you want when the lights are turned off. Turn the lights off take a picture with flash and then adjust your shutter - just your shutter - and take a second image. As long as both shutter speeds are within your cameras sync speed there will be no difference in the two images. This is because flash photography has an effective shutter speed which is the burn time of the flash, in most cases somewhere around 1/1000th of a second. This effective shutter is much much faster then even the cameras fastest sync speed (for most Canons 1/250th) As long as you understand this you understand how to mix flash with ambient light.

The how too blend flash and ambient is actually quite simple. Set your scene, set your camera for an ISO you are comfortable with and set your aperture to create the Depth of Field that you wish to have and set the shutter to your maximum sync speed. Once this is done set your flash output to properly expose your subject (depending on your flash this can either be done with output, neutral density gels, or distance to subject). At this point when you release the shutter you should have a properly exposed image. If you do not adjust your flash power accordingly. 

Once you have a properly exposed image you can then mix ambient light in simply by slowing your shutter speed. Remember from the lights turned off room exercise above that shutter speed does not effect flash exposure, so the Big 3 methodology does not apply to the exposure from the flash and you do not need to adjust aperture or ISO as you change the shutter(this is where people get confused). By slowing or “dragging” the shutter all you are doing is allowing more ambient light to balance the areas of the image that are not being exposed by the flash.

So why do we blend flash and ambient light? There are several situations which can call for this, the most common is when more light is needed then is available yet we do not wish to loose the ambience such as in a club. Another common place to use flash and ambient is when photographing a person at night and wishing to have a city scape behind them visible as well. This is similar to the first but the flash is needed because the person would not expose at all, they would simple be a shadow blotting out the city lights. Another case is to freeze action, such as bullet photography, the flash is used so the bullet can be frozen in the frame and the longer shutter allows the rest of the scene to also be exposed. Another reason to add flash is to create shadows, in the sequence below you can see that the room is very evenly lit and by adding flash I added shadows which creates depth in the images. In actuality blending flash will be used for multiply reasons in the same image.

So now we have covered the theory, lets look at the nuts and bolts of what I did for this exercise and how it affected the images. Photographed at the top you can see how I set the camera and flash in relation to the scene. I treated the piano as the subject of the image, I placed the 600EX-RT on 1/4 power, into a 24” softbox, 6 feet from the piano. The camera was the Canon 6D with the 24-105 f4 L set to 24mm. The ISO was 400 and the aperture was f4 for all of the images in the following sequence the only thing that changes is the shutter speed which is listed on the images.


1/180th

1/125th

1/60th

1/30th

1/15th

These last two images below show the scene, the first with the camera set to take a flash exposure but no power to the flash, and the second with the camera set to take the image just with ambient light. The Canon 6D sync speed maxes at 1/180th which is why there is a discrepancy between the first image in the sequence above and the image here for flash with the flash turned off. In situations where you need a faster sync speed Hi-Speed Sync can be used to get speeds above your cameras sync speed. (This will be covered in a later blog.) For this example I allowed the camera to set the default shutter sync for the 1st image. I also did not correct for Color Balance, the camera was set to Flash which is why the total ambient light image has a yellow cast. I did this deliberately, in the sequence the competing colors make it a little easier to spot how much ambient light is effecting exposure. If you use AWB it will set to flash when a flash unit is attached to the hot shoe so the area exposed by the flash is closer to white. If you use gels to match your environment you will need to set your cameras white balance accordingly with the camera’s custom white balance settings. The exception to this is when using Canon CTO gels with the 600EX-RT. The 600 has a sensor which allows it to correct white balance to the Canon CTO gel being used if the camera is set to AWB. I have not explored this function yet so I am not sure how well it works. It also only works if the flash is mounted in the hot shoe.

No Flash 1/250th

Ambient Only 1/15th


So that is the basics of mixing flash with ambient, like color balance the only way to really learn this skill is through practice. Depending on your set up it is possible that if you are mixing a lot of ambient light you would need to step the flash power down slightly. Do not be afraid to experiment once you have a good grasp on how the toe exposure models work and how well they blend.







Follow Us



Sunday, August 18, 2013

What is Color Balance?


One of the more common mistakes beginning photographers make is not getting good color balance. In most situations, particularly with cameras introduced in the last 3 years the auto white balance function of the camera does a fairly good job most of the time, where it tends to fall flat are areas with mixed light temperatures, so after a brief intro to what color temperature is I am going to focus on ways to correct mixed light situations.

So what is Color Balance? To understand color balance (also commonly incorrectly called white balance) you need to first understand that all light has color. The Color of the light is referred to as color temperature and is measured in degrees kelvin. The warmer the light, that is the more yellow, orange or red the light is the lower the color temperature, as the light gets closer to white and then blue the temperature in degrees kelvin goes up. This seems backwards at first glance, but remember when iron is smelted it starts with a low red glow as it gets hot enough to forge it moves to letting off orange light and when it is hot enough to pour iron starts pushing into the yellow colors. Another way to remember that the high temperatures are the whites and blues is to think of arc welders or lighting. Electric arcs are one of the hottest things we can observe, with temperatures exceeding those of the surface of the sun, and they are in the white and blue color space. For a more complete run down of color temperature click here.

Now you have an idea of what color temperature is, how does it work with color balance? Color Balance is matching the light sources so they all of the same or very similar color temperatures so the camera can then shift the sensor to read white objects as white. It is a subtle but important difference between color balance, matching the light sources, and white balance, setting the camera to read the light sources correctly, but it is an important distinction. It is also why the auto white balance setting will always fail in mixed light. The other common mistake is having a camera set to daylight (essentially white light) and to take photos under artificial light, this is what gives photos that ugly yellow, yellow orange, or yellow/green cast. 

Modern artificial lights tend to be pretty close to 3000k without any green tint. As this gets more common, lower end cameras are tending to have one artificial light setting. High end cameras ,on the other hand, may have four or five artificial light settings (not counting flash, which is generally balanced for daylight). These multiple settings can more closely match the most common color temperatures of incandescent (orange/yellow to yellow) and florescent (yellow to yellow with a green tint) lights. Having these multiple presets can be a quick way to find a suitable white balance if you can not preform a custom white balance. I am not going to go into setting a custom white balance beyond mentioning it is a good idea to use a grey card, because different manufactures have different methods for achieving a custom white balance reading. Consualt the camera’s manual.

For this post I am going through a quick exercise of matching a 5600k Speedlite with modern florescent recessed canister lights. Here is a quick look at the equipment used. For the flash I used a Canon 580EX-II and to match the color of the ambient light I used LumiQuest gel holder. In the photo the gels on the left are used for color correction, The two at the top are a one stop and a two stop neutral density gels which can be used to cut flash intensity on flash units with a fixed power output. The gels on the right are used for Creative Lighting with Color (an upcoming post). For this entry I am only going to speak about the gels on the left. Starting at the top and moving counter clockwise we have a 1/2 stop (or cut) Color Temperature Green (CTG) followed by a 1/4 cut CTG, 1 cut Color Temperature Yellow (CTY), 1 cut Color Temperature Orange, 1/2 cut CTO, 1/4 cut CTO and finally a 1/2 cut Color Temperature Magenta. 

Speedlite with Gel Kit
Speedlite with Gel Kit

As a general rule the CTY and one of the CTGs will be used together to balance older florescent lights, newer florescent bulbs do not tend to have the green tint. The CTO,s will be used for incandescent, but actually look to see what color/s  are most prevalent. The CTM is used on your subject, usually used as fill, when the subject is placed in a green screen environment. In a green screen environment background light reflects off of the screen and will give the subject a green cast. By using a CTM on the subject the green tint is neutralized. If you use photo editing software in the white balance section you have probably noticed a slider that goes from yellow on the left to blue on the right and a second slider that goes from magenta on the left to green on the right. These colors are directly opposite each other on the color wheel and mixing them together neutralizes there impact. In effect your camera does this as its white balance function.

Ok, now you have the theory, lets look at it in practice. All four of these images are just a succession of photos of a white wall. The first image below is the color of the light in the room from the canisters lights when the camera is balanced for the color of the flash. The second images shows the flash firing and the ambient light being crushed out by the camera’s high shutter speed. When this is an option this is the best fix for the light. But it is not an option if you want a slower shutter speed to allow motion blur, or if you are shooting in an environment where blasting everything to white would not look natural, like a club for instance where doing so would destroy the ambience. I have included the histograms so you can better understand the differences in the light color that is causing the shift in the light. 

Image 1 and Image 2
Image 1 and Image 2

Looking at the first image you can see the light in this room has a definite orange cast to it, and looking at its histogram you can see how spread out the different colors of light are. Looking at the second image you can see how the light casts a gradient across the wall, even though the histogram covers a large part of the graph it is fairly uniformly grey as all of the colors are mixed fairly evenly giving us white light. 

The third and fourth images show blending and then correcting the light. In the third image the flash has not been adjusted but the shutter has been drastically reduced so that both the flash and the ambient light can expose the image. The gradient in this image from bottom right to top left clearly shows why the auto white balance in the camera can not adjust to this situation. There is not one uniform light color for it to adapt to and correct. You can also see how the histogram is all over the place even though this is just a photo of a white wall. The fourth image was taken with a 1/4 CTO placed over the flash and the white balance in the camera shifted from flash to florescent, this is because the flash is now pretty closely blended to the ambient light of the room which is pretty close to the florescent preset. 

Image 3 and Image 4
Image 3 and Image 4

Looking at the histogram we can tell it has not been perfectly balanced, but an exact balance is not possible with gels. At any rate it is much closer now the color is no longer painful to look at with only minor corrections needed in the computer. Corrections which can be applied across the whole image rather then trying to blend in different layers of correction, a much more difficult task. 

For these last two images I raised the flash to above the eye line as that is more typical for portraiture, as a result the gradient shift from the third images is seen here in the fifth images from top right to bottom left. The fifth image gives an idea of how difficult it would be to correct the color balance in the computer rather then only needing a minor adjustment to the over all white balance of the sixth photo taken in a close color balanced situation. The complete chaos in the histogram of the fifth image gives a clearer picture, even though the scene is very color neutral the histogram is all over the place.

Image 5 and Image 6
Image 5 and Image 6

All six of these images were shot on a the Canon EOS 6D camera with the 24-105 f4 L. The lens was set to 58mm the camera was set to ISO 400, f8 and a shutter of .4 seconds with the exception of the second image which had a shutter of 1/180th of a second to crush out the natural light. The flash was located 45 degrees camera right and was set to manual 1/32 power 14mm.


Follow Us





Sunday, August 4, 2013

3 Point Lighting

3 Point Lighting
3 Point Lighting

3 point lighting really should be looked at as the fundamental building block for all lighting in both photography and video. I do not make this statement as a judgement, in no way do I mean that the light setup shown here is “the best”. The best light is what is need for the image being created. But what I do mean is that these 3 aspects are present in all lighting setups and need to be considered whether you are using one light mounted on the camera or a 20 light studio set. In all lighting cases you will be working with and should be thinking in terms of Key Light, Fill Light and Background Light, your three fundamental lighting aspects. All other lights, hair lights, rim lights, kickers are just added fluff used to better define how the light falls on the subject and how the light separates the subject from the back ground.

A little bit of house keeping - the camera used was the Canon 6D with the 24-105 f4 L lens, the camera was located 6 feet from the subject on a tripod set to ISO 200 f8 1/160. The lights used were Canon Speedlites set to manual the background light was the 600EX-RT and the Key and Fill lights were both 430EX-IIs all three lights were set to manual. I include this information because a lot of people do ask about it - but really the equipment is not important, understanding how it is being used is what matters. If this is your first article on lighting I would suggest also reading Lighting Your Subject and Part II as well as looking at the resources linked in those two posts.

Key LIght
Key Light
Key Light, the Key Light is the main light in the lighting set up. While the methodology of studio lighting can seem intimidating when you first approach it the Key Light is really the only light you need to really understand. As long as you get the Key Light correct everything else really just slides into place. The Key Light is the main light falling on your subject and is also commonly referred to as the subject light. The Key light sets the direction and quality of the light in the image and in general will provide the mid-tones to highlights of your subject in your image. I say in general because not all photos use the full tonal range. Your Key Light will determine your exposure settings, even if you are wanting a very high key image with the background blown out you will determine exposure based on how your key light falls on your subject. In the example shown here the Key Light is a Canon 430EX-II set to camera right at 45 degrees from the subject, slightly elevated at a distance of 1 1/2 feet and sett to 1/16th power and 14mm.







Fill Light
Fill Light

Fill Light, in many ways the Fill light functions much like the Key Light but instead of defining the mid-tones and highlights it defines the shadows. While light defines your subject the shadows define the mood of the image. In the example shown here the Fill light is a Canon 430EX-II set to camera left at 45 degrees from the subject, placed at the same hight as the subject, at a distance of 1 1/2 feet, set to 1/32nd power and 14mm. Generally a Fill Light will be set somewhere between 1 and 3 stops lower then your Key Light, however there is no correct way to set it - there is only what is correct for your vision, let your vision guid both the placement and the intensity of your Fill Light. I frequently work with the fill light mounted on the camera or even set as far around the subject to be at 180 degrees from the Key Light. If I want the lighting to be quite flat the Fill will be set to almost the same power as the Key, maybe only 1/2 stop lower or if I want the image to have a lot of drama I may turn the Fill off.





Background LIght
Background Light
Background light, the background light does exactly what it sounds like, it lights the background. If you go back and look at the previous two lighting articles linked above you will notice that the background is lit by spill coming form the Key Light in those examples, in some cases it is lit quite a lot while in others there is very little light falling on the background. By adding a background light you can gain control over how the background displays in the image. The Background light was a Canon 600EX-RT placed directly behind and below the subject, gelled blue, at a distance of 12 feet from the wall, set to 1/4 power and 28mm. As you can see the background light is set considerable higher then the other two lights. This is not a hard and fast rule, it was what was need to get proper illumination of the background.

Above I mentioned that as long as you have control of your Key light all of the other lighting will slide into place. The background light can be the best example of that. In the images for the articles linked above the background light had not been considered at all. Only the manor in how the light fell on the subject was taken into account, whether or not the light also happened to spill into the background was not thought about or corrected. The easiest way to control spill is with  light fall off, by placing your Key and Fill lights as close as possible to your subject and turning the power down while moving your subject as far as possible from the background you can prevent most spill, the other option can be to use a flag (dark fabric or panel) to prevent the light from traveling in an unwanted direction.

In this post you can see that I have created 4 distinctly different images without changing any of the camera settings or even recomposing the shot. The important thing to take away from this blog entry is get your Key Light right. If you think about it all four of the above images were set and determined by the Key light, yes even the silhouette is set up by first determining the Key light. For that image I want the Key Light output to be zero and the Fill light to be less then that. Once I have a dark image I then just mix in the correct amount of Background Light to match my vision. That is exactly what happens with every other light whether you are shooting with one or 100, set the Key and then just mix the other lights in to the intensity and direction to create what you envision.

If you look at the images in An Introduction to lighting Your Subject you can see an example of how one light can be used to control all 3 aspects of lighting, all 3 points. It also helps demonstrate why the Key light firing from the camera directly at the subject is bad, it ends up functioning as fill and background light and there is no practical way to control all three aspects. However simple by turning the flash and bouncing it off of a nearby wall or ceiling you can then gain control not just of how that flash functions as a Key light but how much fill it provides and how it falls on the background.


** As an aside the lighting set up shown here is an excellent way to display products, I highly recommend it for your eBay photos, it is also a good place to start with lighting people for portraiture though for portraiture you want to pay a lot more attention to exactly where the Key light is positioned in relation to your subject and their pose. In both cases pick a background color that compliments the subject.




Follow Us



Sunday, June 23, 2013

Lighting Your Subject - Moving the Flash Off Camera, Part II


This is a continuation from last weeks blog, in this installment we are going to look at how light direction effects your image. For this series of images I was shooting with the Canon EOS 60D camera with the 28-135mm f3.5-5.6 USM Lens set 44mm, the aperture was set to f8, the ISO to 800, and the shutter was set at 1/250th. The camera was placed on a tripod and located 3' in front of the subject. The subject was 6' from a white wall which served as the background. The flash I was using was the Canon Speedlite 430EX-II on manual set to 24mm and 1/64th power. The flash had no modifier, and was located 3' from the subject. These setting for both the camera and flash were constant for all six exposures, the only element that changes is the direction the light is falling on the subject. Sitting in for the subject for these images was "The Face" a plywood cutout I hacked together, though a clay mask or mannequin would also make a great subject. These objects are a better stand in when you first start experimenting because they do not move, ergo the only differences will be caused by the placement of the light.

Flat Lighting
Flat Lighting



This first image was taken with the flash mounted directly on the camera. As I mentioned in An Introduction to Lighting Your Subject, this is considered the worst way to use flash. Lighting in this manor is very flat and has the effect of making a person look heavier. This is just one of many factors that contribute to the belief that "the camera adds 10lbs". In actuality it is a combination of several common mistakes that cause this illusion. 







Butterfly Lighting
Butterfly Lighting



This second image is an example of "butterfly lighting", which gets its name from the small butterfly shaped shadow cast by the nose of the subject. This style of lighting is frequently done with a beauty dish and can be very flattering, particularly for young attractive women. This lighting style draws attention to the eyes and face, while emphasizing the cheekbones and jaw line. Unfortunately "The Face" lacks proper definition to truly display these attributes. The light was raised 2' above the camera and moved forward slightly to maintain the 3' distance to the subject.





45 Degrees Camera Right
45 Degrees Camera Right






This third image was created by moving the flash 45 degrees to camera right, in this image the flash was on the same plain as it would be when mounted to the camera. As a general rule portraits are not shot with the light positioned here as the shadow cast by the nose tends to make the nose look wider.







Loop Lighting
Loop Lighting






This fourth images is an example of "Loop Lighting", the name is derived from the loop shaped shadow cast by the nose. This style of lighting is very common in portraiture, it tends to be the most flattering for the widest audience, particularly if you use softer light and add some fill both of which will help to even skin tone, hide blemishes and reduce the appearance of wrinkles. It is also closely related to Rembrandt Lighting which I will cover In depth in a later blog entry.






Split Light 90 degrees camera right
Split Light 90 degrees camera right



















Split Light 90 degrees camera right up 30
Split Light 90 degrees camera right up 30

These last two images are examples of Split Lighting. In this style of lighting the light comes in to the subject from 90 degrees, effectively splitting the face into a lit side and a shadow side. 





















It is important to note that for most of the lighting styles mentioned here the direction the light falls on the subject is much more important then the placement of the light relative to the camera. For instance, if you are stuck with a point and shoot camera and you have to use on camera flash, having your subject turn their head thirty degrees to the side and tilting their head towards the camera will use the on camera flash as Loop Lighting. This will add some definition to the shape of the face, with a little practice you can help your subject further by twisting their shoulders slightly so you can elongate the neck to eliminate excess chins. In this manor a photographer can make up for some of the limitations of having to use on camera flash. 

At this point some of you are probably wondering why I have written three blog entries on lighting but I have yet to talk about "proper exposure". In general proper exposure is considered to be exposure for the mid-tones, however if you are shooting low key photography most of your image will be very dark to black and little of the mid-tones will actually be exposed. Also, above I made general statements about when certain lighting styles tend to be used, but I have not referred to any of them as "proper" (with the exception of mentioning trying to avoid Flat Lighting), nor did I make that kind of judgment in the previous article on hardness. In all of these cases what is "proper" depends entirely on your vision as an artist, including the use of Flat Lighting. In all of these cases you should make it a conscious decision to use a specific style quality and intensity of light. 

I will say though, having sufficient contrast is important, that is the range from light to dark. What is a frequent mistake in photography, particularly in interior ambient light, will be the presumption that no flash is better then on camera flash. A person will opt to turn the flash off because there is enough light to shoot without it. But this is usually the case in buildings with lots of strip lighting. Everything is lit very uniformly and the dynamic range for the entire exposure may only be about half a stop. This lighting is ok for our day to day existence since we are seeing that environment with two eyes, but seen through the lens of a camera the image will end up being very muddy. Turning on your flash, using it at low power and letting it be a little bit of a kicker for an ambient exposure can do a lot to combat what would otherwise be a waste of a shutter release even though it is "properly exposed". Adding flash will add contrast which will ad pop to what would otherwise be a blah image.  

This should give you a couple of more tools to add to your photography trick bag. Good photography can be daunting, but if you break it down into digestible pieces you can really start to get a good handle on what you are shooting.






Follow Us


Sunday, June 16, 2013

Lighting your Subject - Moving the Flash Off Camera

I have frequently mentioned the importance of using light to control light and by extension to control exposure so that you can then use Aperture, Shutter and ISO more creatively. But to control light with light you first need to understand light and what element it adds to photography. For this post I am going to look at a particular aspect of light, hardness, and its contrasting aspect, softness. All of these photos were taken with the EOS 6D mounted on a tripod 4 feet from the subject. The ISO was set to 1600, the shutter to 1/160th, and the aperture to f16 and the lens was at 105mm for all of the images. The main light, or Key Light if you will, was a Canon Speedlite 580 EX-II set to 35mm placed 45 degrees to the subject on camera right and triggered by a Canon Speedlite 600 EX-RT. My subject was 8 feet from the white wall that served as a background. All of the above setting were locked for all of the photos. The light quality was changed with modifiers and distance of the light to the subject. The power output of the light was adjusted as well to maintain proper exposure for the midtones.

Let me just take a moment and go into hardness or softness of light before we continue on to the photos. What is Hard Light? The short answer is that hard light creates a hard edge to the shadows and soft light creates a gradient transition from light to shadow. If you have not looked at An Introduction to Lighting your Subject go ahead and take a moment and look that post over. The second and third images from that post show nicely the difference between hard light and soft light. For the photos below I sat in as a subject so that these differences could be easily observed on the human form.

Ok now we have an idea of what hardness means, how do we control it? The simplest way to think of it is that hard light is a small light source and soft light is a big light source. However the size of the light is not the only thing that effects hardness. Hard light is very uniformly directional. This is a by product of the size of the light but also the distance of the light and what type of modifier the light has in front of it. Perhaps the easiest way to picture this is to think of sunlight on a clear day. The Sun is huge which should create soft light - but it is very very very far away which makes it very very very small in appearance which is what makes sunlight so hard. On the other hand if you go out on an overcast day the whole sky functions as a soft box and shadows can almost completely disappear. What follows are a series of 4 images with a brief description on set-up.

This first image has the hardest light quality, the 580 EX-II Speedlite was mounted in an Interfit Strobies S Bracket with a 7” reflector and a honeycomb and was placed at 9 feet from the subject. The reflector and honeycomb make the flash effectively a 7” light source. The second image has the same modifier but is moved to 3 feet from the subject. It is possible to see a slight softening of the light between the two images, however the light quality still remains quite hard, this is because at 7” the light source is still smaller then the subject even at the closest distance. Another way to picture soft light verses hard light is, soft light is from a source that is bigger then your subject, hard light is from a source that is smaller than your subject.



Light 9' Reflector w/ Honeycomb
Light 3' Reflector w/ Honeycomb


For comparison the soft light from both the 3’ and 9’ distances is using a 36” square soft box. This is a much larger light than the reflector and honeycomb and the softening effect of the larger light is much more evident. In the interest of going from hardest to softest the 3rd images is of the soft box and 9’ and the 4th is with the soft box at 3’. The closeness of the light in the last shot makes it the largest light source in the series.

Light 9' w/ 36" Soft Box
Light 3" w/ 36" Soft Box
This is a brief look at lighting your subject with an off camera key light. A couple of things to point out. The first is that in the interest of changing as few elements as possible the hight of the light was not changed, only the distance to the subject. If you compare the 3’ images to the 9’ images it is easy to see that the hight of the light was much more appropriate for the images at 3’. As you start to experiment with light you will want to light your subject from a higher angle then they are. When you move your light further away the light will need to be raised in order to maintain that angle. Generally light from somewhat above is more flattering. The second thing to notice is that in both of the 9’ images the key light is starting to light the background. It is much more pronounced with  the 36” soft box because the light from that modifier is much less directional, it spills around the room and much more of the light lands on the background. As the light is moved from the subject the ratio between the subject and the light and the background and the light decreases meaning that enough light is starting to fall on the background for the background to expose in the image. I deliberately set up in front of a distracting background so that the use of a closer light source, not only to create softer light but to control light spill in other areas of the frame could be observed. One easy way to get rid of background distractions is to not light them. This is why ISO is not an effective way to control light.

At any rate this should give people a starting point for experimenting with light. Light can seem overwhelming when you first move from natural light and being locked into The “Big 3” and move into modified light. But if you break lighting into small easily understood pieces then you can start to build a skill set which will serve not only with flash, but will allow you to modify ambient and natural light as well.




Follow Us